Genuine Honda Oem

3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG

3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG
3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG
3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG
3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG
3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG

3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG    3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG
Want to lift your 1997-01 CRV the right way? With our bolt in suspension spacers you'll get up to 3 of lift while maintaining stock ride quality. Works with stock OEM springs and struts. Basic kit comes with 2 1.5" spacers for front and 2 2.5" spacers for rear. Includes all necessary hardware and detailed installation instructions.

Does not include camber correction kits which are necessary for getting an alignment after installing this kit. For a kit with these parts included, please see our other listings. Note: This kit cannot be used with an existing lift. For off road use only!

Please see our other listings for more lift kits and parts. Lift chart for 1.5 spacers. 1988-00 Honda Civic Front: Approximately 2.5 of lift. 1988-95 Honda Civic Rear: Approximately 2 of lift.

1996-00 Honda Civic Rear: Approximately 1.75 of lift. 1997-01 Honda CRV Front: Approximately 3 of lift. 1997-01 Honda CRV Rear: Approximately 1.75 of lift.

Lift chart for 2.5 spacers. 1988-95 Honda Civic Rear: Approximately 3.25 of lift. 1996-00 Honda Civic Rear: Approximately 3 of lift. 1997-01 Honda CRV Rear: Approximately 3 of lift. 205/70/15 26.3 (stock CR-V size). All vehicles are different and lift height can vary due to the condition of the suspension before installing the kit.

These numbers are averages from real world measurements before and after the kit, and should only be used as general guidelines. Q: How is the amount of lift measured? A: The amount of actual lift is measured from the fender lip to the ground.

Q: What size tires can I run on my CRV after installing this lift kit? A: You can fit a 215/75/15 with minor adjustment to the pinch weld in the back of the front fender. You can fit 235/75/15 tire with some trimming of the plastic.

A 30+" tire will require a 4" lift or significant trimming to fit. We also recommend wheels with lower offset (backspacing) or wheel spacers to add clearance for the larger tires.

Q: Will I need an alignment after installing this kit? A: Yes, just as if you lowered your car, lifting changes the wheel alignment. It is also recommended to install camber correction kits for lifts greater than 1. Q: Will lifting my car affect the axles?

It depends on the amount of lift and the type of axles you have in your vehicle. Worn original or parts store rebuilt axles are more prone to having issues. This kit is designed to solve the axle issues common to lifting the 97-01 CRV. However, lift heights can vary depending on the condition of the existing suspension and therefore we cannot guarantee there will be no axle issues.

For best results, install new axles and do not combine this kit with lift springs or other spacers. Q: Do I need to replace my suspension bushings when installing a lift kit? A: It depends on the condition of your existing bushings.

We always recommend inspecting your factory bushings and replacing them with urethane bushings such as Energy Suspension if needed. The added benefit of installing urethane bushings is that it allows the suspension to move more freely. We also recommend replacing sway bar end links on 97-01 CRV after 100k as they tend to rattle when going over bumps. A: In most cases, yes.

By lifting the suspension you are effectively raising the roll center of the car, which can cause additional body roll. Our lift kits are intended for off-road use where suspension travel and ground clearance are more important. The item "3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG" is in sale since Saturday, March 9, 2019. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Suspension & Steering\Lift Kits & Parts". The seller is "hrgengineering" and is located in Mooresville, North Carolina.

This item can be shipped to United States, Canada.

  • Country/Region of Manufacture: United States
  • Lift Height: 3" Front and Rear
  • Adjustable: No
  • Type: Kit
  • Manufacturer Part Number: HRG-3RD1LK
  • Part Type: Suspension Lift Kit
  • Included Hardware: Mounting Hardware
  • Placement on Vehicle: Front
  • Brand: HRG Engineering
  • Fitment Type: Performance/Custom
  • Warranty: Lifetime


3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG    3 basic lift kit for Honda CRV CR-V 1997-01 RD1 suspension spacers HRG